 SBC Parts, Double hump heads, Pistons, Rods, And Others... |
  |
 Jan 28 2010, 01:15 PM
Post
#1
|
|
|
Cool Newbie Group: Members Posts: 50 Joined: 26-September 08 Member No.: 9,600  |
I have some SBC stuff im gonna sale... its just sitting around taking up space... Can get pics of anything if there is interest...
I have 1: (7) 4.030 dome pistons. have floating wrist pins and snap ring locks included. not sure who they are made by, Part number: 7009p on the top, under is 338-99 E ... $75 OBO 2: (7) "I" beam rods. floating pin design. again not sure of make, Appear to be reconditioned stock 5.7" rods that were made to work with a floating pin. $100 OBO Or $150 for the rods and pistons, they are still assembled... 3: Afco Steel 4 blade fan. BRAND NEW $20 4: Heads from 89 chevy 350 truck motor $50 Casting Numbers: 14102193...87-up...305/350......1.94"/1.5" valves from mortec website.. 5: set of double hump heads. SOLD!!! 6: Fabricated welded aluminum valve covers. $75 obo 7: Single BARE Sbc head. Has knicks in one combustion area... not bad at all can get pics. Good if your looking for a match... $75 obo Casting number: 3782461 61-70 1.94/1.50 & 2.02/1.6 250-375 64 CC Chambers No bolt holes These are the double humps. Info from same place as above... This post has been edited by derby217: Feb 14 2010, 02:34 AM |
 |
 
|
|
Jan 28 2010, 11:14 PM
Post
#2
|
|
|
Cool Newbie Group: Members Posts: 54 Joined: 3-August 09 Member No.: 11,212 |
QUOTE (derby217 @ Jan 28 2010, 01:15 PM)  I have some SBC stuff im gonna sale... its just sitting around taking up space... Can get pics of anything if there is interest... DO the valve covers have breathers ? I have 1: (7) 4.030 dome pistons. have floating wrist pins and snap ring locks included. not sure who they are made by, Part number: 7009p on the top, under is 338-99 E ... $75 OBO 2: (7) "I" beam rods. floating pin design. again not sure of make, Appear to be reconditioned stock 5.7" rods that were made to work with a floating pin. $100 OBO Or $150 for the rods and pistons, they are still assembled... 3: Afco Steel 4 blade fan. BRAND NEW $20 4: Heads from 89 chevy 350 truck motor $50 Casting Numbers: 14102193...87-up...305/350......1.94"/1.5" valves from mortec website.. 5: set of double hump heads. complete with valves and springs. $250 Casting Numbers: 3917291 62-69 1.94/1.50 275-350 64 CC Chambers No bolt holes These are the 'Turbo' heads From Dirt forum Casting numbers http://www.thedirtforum.com/castings.htm 6: Fabricated welded aluminum valve covers. $75 obo 7: Single BARE Sbc head. Has knicks in one combustion area... not bad at all can get pics. Good if your looking for a match... $75 obo Casting number: 3782461 61-70 1.94/1.50 & 2.02/1.6 250-375 64 CC Chambers No bolt holes These are the double humps. Info from same place as above... |
|
|
|
|
Jan 31 2010, 04:31 PM
Post
#3
|
|
|
Cool Newbie Group: Members Posts: 69 Joined: 4-July 07 From: Orangeville, Ohio Member No.: 7,714 |
are the turbo heads ready to go? or in need of a rebuild?
|
|
|
|
|
Jan 31 2010, 05:57 PM
Post
#4
|
|
|
Cool Newbie Group: Members Posts: 50 Joined: 26-September 08 Member No.: 9,600 |
QUOTE (J. MAC @ Jan 31 2010, 03:31 PM) are the turbo heads ready to go? or in need of a rebuild? As of now, i have a deal pending on the pair... But for a race app, i would freshen them up... |
|
|
|
|
Feb 6 2010, 12:31 AM
Post
#5
|
|
|
Cool Newbie Group: Members Posts: 69 Joined: 4-July 07 From: Orangeville, Ohio Member No.: 7,714 |
did that deal on the heads work out?
|
|
|
|
|
Feb 6 2010, 10:52 PM
Post
#6
|
|
|
Cool Newbie Group: Members Posts: 50 Joined: 26-September 08 Member No.: 9,600 |
was to meet the guy today, but the snow put a stop to that... will let you know if it falls through... Thanks DAVE
|
|
|
|
|
Feb 7 2010, 02:21 PM
Post
#7
|
|
|
Cool Newbie Group: Members Posts: 69 Joined: 4-July 07 From: Orangeville, Ohio Member No.: 7,714 |
ok. thank you
|
|
|
|
|
Feb 8 2010, 08:30 PM
Post
#8
|
|
|
Cool Newbie Group: Members Posts: 50 Joined: 26-September 08 Member No.: 9,600 |
J. Mac sent you a message... DAVE
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 9th September 2010 - 10:12 AM |