191 replies to this topic

[Drt35]

This list is updated so you do not need to read 10 pages oil cooler 6.125 inch Eagle LJ Small Block Chevy Connecting Rods 6 not full set 3.5 inch Vortex cone muffler inserts $20 each Dodge Small block headers for Rocket or ? $100 6 inch Crower Sportsman rods with pistons Only 6 $80 Lots of Small block Chevy pistons Broken sets for parts Barnes in the pan oil pump for Chevy $100 Oil to water heat exchanger $40 Small Block Chevy factory iron 2 and 4 barrel Q jet intakes Lots of stock iron heads no Double humps Shaft Rocker parts and sets for small block Chevy Lots of misc. fittings 20 Springs for late models too many to list $10 each or buy all Solid roller lifters $100 set 98 Ford truck hood white very good shape $100obo New MSD Knock Alert $110 Brodix 1801 Intake for sbc 18x heads with Dominator Carb flange and removeable plate on intake side for tall block ported $300 Small block Chevy Solid Roller Cams Too many to list $100 to $200 Used roller cam valve springs $10 set and up 350 2 bolt block $50 obo 305 short block needs rebuilt $100 May have Racesaver Sprint Numbers 400 block 2 bolt .030 overbore also cut for stroker 3/4 fill hard block with head and main studs a little rust $250 400 complete motor made noise $300 turbo 350 trans cores $50 Pontiac turbo 400 trans cores $100 4.4 / 267 sbc iron stock crank same as 305 and 350 just lighter $75 each Aluminum Moroso Tall Small block valve covers damaged $5 pr Standard weight 2 piece flywheels for Chevy $40 Clutch covers pressure plate $20 obo 4.159 Bore SB2 Chevy RCR pistons $100 obo set of 8 4wd Chevy Transfer case and 350 auto trans $50 each K1500 Front axle early 80s $30 GM Bowtie 18 degree intake ported Stolen at Washington 350 4 bolt block std bore $150 Shocks Carrera some split valves and gas $50 and less Afco 2" threaded body cones, nuts and top bearings Top and bottom lift bar brackets for Rocket Rocket birdcage parts for non-bearing birdcages no complete sets Spreadport LM headers only 2 left sides 1 new Dynatech for Rocket $75 1 used for ? $30 1 Right side used $25 or $100 all. Call 724 537 3566 leave message. Please call before 9 pm. PM me with web address for pics. Make reasonable offer. Many more parts not listed. This list is updated so you do not need to look at 10 pages. List good 3/2/14

Edited by Drt35, 02 March 2014 - 12:20 AM.

[Drt35]

May deliver to racetrack or swap meet

[Drt35]

back to page 1

[race ace]

do you happen to have any 9 inch heim's end shocks for a street stock? if so how much ?where are you located ?

[Drt35]

do you happen to have any 9 inch heim's end shocks for a street stock? if so how much ?where are you located ?

I think I have at least 1 9" steel Afco and a few steel Carreras , not sure if 7 or 9 inch. Probably $10 or 15 each. Near Latrobe PA. thanks Bob

[Drt35]

back to page 1

[81lucas]

do you still have the fuel cell? if so call mike 814 933 6099

[Drt35]

do you still have the fuel cell? if so call mike 814 933 6099

Yes still for sale. Give me a call 6pm to 9pm. 724 537 3566 thanks bob

[i'll be back]

do you still have the two 850 gas carbs and what were they run on. how much for both? thanks scott

Attached Files

•  drivers_side.jpg   49.45KB   147 downloads

Edited by i'll be back, 10 May 2009 - 09:54 PM.

[Drt35]

do you still have the two 850 gas carbs and what were they run on.


how much for both?


thanks scott

Still have both 850 gas carbs. Bought as spares and never used. $200 carb may be useable or need gaskets, $125 carb will need some work. $275 cash for both. thanks Bob

[i'll be back]

thanks but i need somthing i can bolt on and go thanks scott

[Drt35]

back to page 1

[Drt35]

back to page 1

[racing2219]

do you have krc power steering pump

[Drt35]

do you have krc power steering pump

Still have it, hex drive for mounting on dry sump, fuel pump or cam. PM me with email for pic. thanks Bob

[Drt35]

back to page 1

[chance2]

im interested in the 400 block 2 bolt .030 overbore also cut for stroker 3/4 fill hard block with head and main studs $250 do you still have this and where are you located 2chance@windstream.net or pm me

Edited by chance2, 01 July 2009 - 02:10 PM.

[Drt35]

do you still have the main studs and are they for a 350 if so what brand also?

Studs go with the 400 block. Located near Latrobe , PA.

Edited by Drt35, 01 July 2009 - 08:00 PM.