12 replies to this topic

[Retort]

Need 3 speed Chevy trans that has been converted to no tail shaft open drive. Or the parts or part numbers to build one of these. leads to any old vintage hardware appreciated. Thanks Gene 419 287-4871 steele@wcnet.org

[fordblueoval]

For your vintage modified projects, I have two RPM transmissions and two bellhousings for $250. You already know where I live. Charlie

Attached Files

•  IMG_0592.JPG   848.02KB   61 downloads
•  IMG_0591.JPG   1.04MB   50 downloads
•  front_view.jpg   994.89KB   29 downloads
•  one.jpg   704.25KB   36 downloads
•  bottom_view.jpg   738.37KB   14 downloads

[Drt35]

Need 3 speed Chevy trans that has been converted to no tail shaft open drive. Or the parts or part numbers to build one of these. leads to any old vintage hardware appreciated. Thanks
Gene 419 287-4871
steele@wcnet.org

I see parts like this and other vintage stuff at Don Kreitz open house and parts swap. But it is the Saturday after Thanksgiving and near Reading PA. Probably Dingo on here or Bud Garvey can help you with vintage stuff.

[Dingo]

I see parts like this and other vintage stuff at Don Kreitz open house and parts swap. But it is the Saturday after Thanksgiving and near Reading PA. Probably Dingo on here or Bud Garvey can help you with vintage stuff.

DAMN Gene..... I had two of those and advertised them for a year - no takers. In the finish I scrapped them when I had a big clean out about 6 months ago. If I'd known you wanted them, you could have had them for nothing.

Sorry buddy.

Dingo

Attached Files

•  300315_255528044491771_1403868400_n.jpg   10.1KB   65 downloads

[Retort]

DAMN Gene..... I had two of those and advertised them for a year - no takers. In the finish I scrapped them when I had a big clean out about 6 months ago. If I'd known you wanted them, you could have had them for nothing.

Sorry buddy.

Dingo

I didn't know I needed them till last week. I'm try to get the 72 car together that Bob Wearing ran. I need a front motor plate too.

[Drt35]

DAMN Gene..... I had two of those and advertised them for a year - no takers. In the finish I scrapped them when I had a big clean out about 6 months ago. If I'd known you wanted them, you could have had them for nothing.

Sorry buddy.

Dingo

Looks like Ford parts to me. I have a stock trans like that, but slip yoke maybe. Maybe you can find something at Big Daddys.

[tnt6race]

I might have one for u i will look tomorrow night. if u want to u can call me between 5 and 7 Tomorrow night. If I do I can bring it next Saturday or Sunday to big daddy if you want just call me tomorrow and we can make arrangements Mike turner. 724-290-4612

[scruffy1a]

Need 3 speed Chevy trans that has been converted to no tail shaft open drive. Or the parts or part numbers to build one of these. leads to any old vintage hardware appreciated. Thanks
Gene 419 287-4871
steele@wcnet.org

Check the classified board. That's where somebody would post their vintage trans if they wanted to sell it. Unless they were inconsiderate of other Racestud members. Then they would just post it on the message board.

[manny]

Check the classified board. That's where somebody would post their vintage trans if they wanted to sell it. Unless they were inconsiderate of other Racestud members. Then they would just post it on the message board.

if this really bothers you that much, then dont read it.

[Retort]

Trans and parts have been found Thanks all!

[manny]

Trans and parts have been found Thanks all!

good to hear, now the fun starts

[racin4fun]

i have one under the bench, might have even gotten it from you at some point in time? call sometime 814-336-9880 Dave